Traktor 3.2.2 @ SB Audigy 2 with kX 3537

dns_ · Jul 27, 2007, 03:50 PM

I know this question is been asked like hundreds of times, but by searching and reading the older posts regarding to the same situation, I still couldnt fix my problem.

Here's my current DSP setup (if that helps):
http://www.hot.ee/gphx/kx.jpg
Headphones are connected to the lime-green jack and monitor-speakers to black.

And just like with many other Traktor users, I couldnt get "pre-listen" sound to my headphones. Right now Master output goes to both headphones and speakers. I set my audio routing in Traktor just like in previous posts it has been recommended: Master = 0/1, Monitoring = 6/7. I think the problem could be between MX6 and epilog, but who knows.

Would be great if anyone could help me out, thanks in advance!

Russ · Jul 27, 2007, 06:51 PM

Sorry, I am confused by your config, are you recording something? or using ASIO input for something? (I am guessing that you are not).

Get rid of MX6 as it should not be needed here, and get rid of ProFx:ASIO since it should not be used with epilog.

Connect the SRC plugins directly to the Analog Front (FxBus 6/7 - monitor), and Analog Rear (FxBus 0/1 - master) pins of epilog.

i.e. (assuming that you want the Expander on the signal from master)
SRC (FxBus 6/7) --> epilog (Analog Front)
SRC (FxBus 0/1) --> Expander --> epilog (Analog Rear)

The above assumes that Swap front and rear is not enabled in kxmixer (if it is, then reverse the connections to epilog).

dns_ · Jul 28, 2007, 05:14 AM

Quote:

Originally Posted by Russ

Sorry, I am confused by your config, are you recording something? or using ASIO input for something? (I am guessing that you are not).

Get rid of MX6 as it should not be needed here, and get rid of ProFx:ASIO since it should not be used with epilog.

Connect the SRC plugins directly to the Analog Front (FxBus 6/7 - monitor), and Analog Rear (FxBus 0/1 - master) pins of epilog.

i.e. (assuming that you want the Expander on the signal from master)
SRC (FxBus 6/7) --> epilog (Analog Front)
SRC (FxBus 0/1) --> Expander --> epilog (Analog Rear)

The above assumes that Swap front and rear is not enabled in kxmixer (if it is, then reverse the connections to epilog).

thanks for the reply. I use this configuration to record my external synth from line in (using Cubase SX). I actually got it working yesterday by simply having only FXBUS -> epilog, i made kX DSP preset specially for traktor, so it's kinda no problem anymore

dns_ · Jul 28, 2007, 08:21 AM

actually now i faced another problem: when recording, I only get right channel recorded (though I've connected both Left and Right channels in epilog)

Here's my current setup:
http://www.hot.ee/gphx/kx2.jpg

Tracktor works fine with this setup, only the recording has right channel :/
--------
actually now when using k2lt instead of epilog, recording seems to be working fine

Russ · Jul 28, 2007, 12:50 PM

Quote:

Originally Posted by dns_

I use this configuration to record my external synth from line in (using Cubase SX).

Ahh OK. It is hard to tell from the pic as you did not show how the SRC plugins were congifured. In any case, I am glad you got it working.

Quote:

Originally Posted by dns_

actually now i faced another problem: when recording, I only get right channel recorded (though I've connected both Left and Right channels in epilog)

Here's my current setup:
http://www.hot.ee/gphx/kx2.jpg

FxBus should not be directly connected to RecL/RecR of epilog, or you may get the above behavior (this is a known issue). Insert a Vol plugin or GainHQ (or whatever) in between (as a buffer) and it will work (or you can use kxlt (as you discovered)).

imperia · Aug 1, 2007, 09:01 AM

http://imperia.kicks-ass.net/KX/dsp_setup.jpg
here is my dsp setup i am using for traktor and everything