Routing Signal from One Soundcard to another without cable?

burli · Jan 4, 2007, 06:40 PM

Hello!

If have installed two soundblaster Live with the KxDrivers. Is it possible to Route one Output of Soundblaster one to an input of Soundblaster 2 without a cable?
The reason is, i need more than 2 analog outputs and with Foobar i can output the signal only to one of the two cards.

Thank you all very much for this great piece of Software and your great support!

Carsten

Doug W · Jan 4, 2007, 07:49 PM

You need the S/PDIF cable to keep the 2 cards in sync. If you look at your 2 cards as HOST and CLIENT, you can tell foobar to output to the CLIENT card. Then, using a DSP that you create you route the output of the

CLIENT card to an SPDIF output -> HOST SPDIF input

You can then route that to the analog front out of the HOST card and route your other application to the analog rear of the HOST card.

Is this what you are trying to accomplish?

Maddogg6 · Jan 5, 2007, 03:40 AM

Did you see this - I never tried it, but looks like what your asking for..
Its not free and its WDM not ASIO.... so....
http://nrcde.ru/music/software/eng/vac.html

burli · Jan 5, 2007, 07:35 AM

Hello!

Thanks a lot for your answers!
@doug:

Year thats exactly what i asked about. I will try it that way. I thought theire might be a solution without cables and Maddog might have found one. I will try both and tell you the results.

@MAddog
Thanks a lot. I will try this solution and post here.

Best wishes,

Carsten

Jan 4, 2007, 06:40 PM	#1
burli DriverHeaven Newbie Join Date: Jan 2006 Posts: 2 Rep Power: 0	Routing Signal from One Soundcard to another without cable? Hello! If have installed two soundblaster Live with the KxDrivers. Is it possible to Route one Output of Soundblaster one to an input of Soundblaster 2 without a cable? The reason is, i need more than 2 analog outputs and with Foobar i can output the signal only to one of the two cards. Thank you all very much for this great piece of Software and your great support! Carsten

Jan 4, 2007, 07:49 PM	#2
Doug W DriverHeaven Senior Member Join Date: Mar 2003 Location: Montevideo, MN USA Posts: 957 Rep Power: 0	You need the S/PDIF cable to keep the 2 cards in sync. If you look at your 2 cards as HOST and CLIENT, you can tell foobar to output to the CLIENT card. Then, using a DSP that you create you route the output of the CLIENT card to an SPDIF output -> HOST SPDIF input You can then route that to the analog front out of the HOST card and route your other application to the analog rear of the HOST card. Is this what you are trying to accomplish? Last edited by Doug W; Jan 4, 2007 at 08:50 PM.

Jan 5, 2007, 03:40 AM	#3
Maddogg6 Tail Razer Join Date: Jun 2005 Location: Bernyurass, AZ - USA Posts: 4,027 Rep Power: 36	Did you see this - I never tried it, but looks like what your asking for.. Its not free and its WDM not ASIO.... so.... http://nrcde.ru/music/software/eng/vac.html

Jan 5, 2007, 07:35 AM	#4
burli DriverHeaven Newbie Join Date: Jan 2006 Posts: 2 Rep Power: 0	Hello! Thanks a lot for your answers! @doug: Year thats exactly what i asked about. I will try it that way. I thought theire might be a solution without cables and Maddog might have found one. I will try both and tell you the results. @MAddog Thanks a lot. I will try this solution and post here. Best wishes, Carsten